Hydroponic gardening for beginners comes down to four things. Pick a simple system with few parts. Use a fertilizer made for water culture. Keep the pH between 5.5 and 6.5. Grow an easy crop like lettuce first.
The numbers below come from university extension services wherever they exist. If you would rather grow in soil, the rest of my gardening section covers that.
As an Amazon Associate I earn from qualifying purchases.
Key takeaways
- Start with a Kratky jar or a deep water culture container, and grow lettuce or herbs first.
- Keep pH between 5.5 and 6.5 for most crops. Read it with a pH meter calibrated at pH 4 and 7, not test strips or color drops.
- Use a fertilizer made for hydroponics. I suggest a three-part base because one set covers greens now and fruiting crops later.
- Feed lettuce and herbs gently, near the low end of the EC range, and keep the reservoir at 65 to 70°F.
- Keep light out of the reservoir and air moving around the leaves to head off algae, root rot and tipburn.
Gear for this guide Paid links
As an Amazon Associate I earn from qualifying purchases. Picked from the makers’ published specs, not from testing.
-
General Hydroponics Flora Series 3-Part NutrientsBest fit. Feeding greens now and fruiting crops later with a fertilizer made for water culture
-
Reeooue Rockwool Cubes and 2-Inch Net CupsStarter option. Starting seeds and holding plants in a Kratky jar or DWC container
-
General Hydroponics pH Control KitHandy extra. Bringing pH back into range with Up and Down, read with a separate pH meter
-
Spider Farmer SF1000 LED Grow LightStep-up option. Indoor growers with no bright window who want steady light for greens
In this guide
- What is hydroponic gardening?
- Is hydroponic gardening good for beginners?
- Which hydroponic system is easiest to start with?
- How to set up a simple deep water culture system
- What pH and nutrient levels do hydroponic plants need?
- How much light do hydroponic plants need indoors?
- What plants grow best hydroponically?
- How to look after a hydroponic garden each week
- Common hydroponic problems and how to fix them
- Where to go from here
- Frequently asked questions
What is hydroponic gardening?
Hydroponic gardening means growing plants with their roots in water that carries nutrients, not in soil. The plant still needs light, carbon dioxide, oxygen, water and nutrients. You just deliver the water and nutrients straight to the roots.
Penn State Extension lists 17 essential nutrients that plants need. In a garden bed, the soil supplies many of them. In hydroponics, the mineral nutrients all come from the fertilizer you mix into the water. That is why fertilizer and pH matter so much more here than in a pot of soil.
Is hydroponic gardening good for beginners?
Yes, if you start small. One container of lettuce teaches you pH, feeding and light without much at stake. Leafy greens grow fast and can be cut more than once, so you get a result early.
Beginners usually struggle when they start too big. They try tomatoes under lights, or they build a pumped system before they know how a nutrient solution behaves. My advice is simple. Start with one crop and one container. Learn to read the numbers. Then scale up. If you have never grown anything inside, my indoor gardening for beginners guide covers space and light first.
Which hydroponic system is easiest to start with?
For a first try, pick Kratky or deep water culture (DWC). In both, plants sit in net pots above a container of nutrient solution. The difference is how the roots get oxygen.
| Kratky | Deep water culture (DWC) | |
|---|---|---|
| Pump | None | An air pump and air stone |
| Solution level | Covers the bottom third of the net pot at the start | Roots sit one third to one half in the solution |
| Topping up | No, the level is left to drop | Yes, kept at a steady level |
| Best crops | Leafy greens and herbs | Greens and herbs, with room to grow |
| Why pick it | Fewest parts, works anywhere | Called the simplest and cheapest system by University of Minnesota Extension |
Either way, you need something to start seeds in and something to hold the plants over the water. A starter pack like the Reeooue rockwool cubes with 2-inch net cups on Amazon covers both jobs.
You will also see wick and nutrient film technique (NFT) systems in beginner guides. A wick system is passive like Kratky. NFT uses a pump to run a thin stream of solution past the roots. Both work, but they add parts. I would save them for a second season.
How to set up a simple deep water culture system
These steps follow the University of Minnesota Extension guide to small-scale hydroponics. A few numbers come from Gorilla Grow Tent, a company that sells grow tents and gear. I mark those “(seller figure)” from here on, so you know which numbers come from a shop and which come from a university.
What you need
- A lidded container that blocks light. A bucket works well, and my bucket gardening guide covers picking one.
- An air pump, tubing and an air stone (DWC only).
- Rockwool or coir cubes and net pots.
- A fertilizer made for hydroponics.
- pH Up and pH Down.
- A pH meter, pH 4 and pH 7 calibration solutions, and an EC meter.
- A grow light, if you have no bright window.
The steps
- Soak rockwool or coir cubes for 24 hours, then sow your seeds in them. I would soak rockwool in water already adjusted into the pH range. Lettuce and basil are easy first picks.
- If you grow under a light, set it on a timer for 12 to 14 hours a day. Hang it at the height the light’s manual gives for seedlings, and raise it as the plants grow.
- Cut holes in the container lid to fit your net pots. Fill the container with water.
- Put an air stone on the bottom of the container and run its tubing to an air pump outside. The bubbles keep oxygen in the water. Missouri Extension says dissolved oxygen above 6 ppm is best, and this is the part that keeps DWC roots from drowning.
- Check the pH of the plain water before you add anything.
- Add hydroponic fertilizer at the rate on the label. With a three-part base like the General Hydroponics Flora Series nutrients on Amazon, add each part to the water on its own and stir well before you add the next.
- Check the pH again after mixing, and adjust it into range with pH Up or pH Down.
- Move seedlings once their roots poke out of the bottom of the cube. Set each cube in a net pot so the roots sit one third to one half in the solution. Clay pebbles packed around the cube are optional. They hold it steady and keep light off the top, but a cube on its own works.
- Keep the growing area above 65°F and the reservoir water at 65 to 70°F (seller figure). I treat 70°F as the ceiling for the water, because warm water holds less oxygen. Lettuce is a cool-season crop, so keep it away from heaters and hot windows too.
Why I suggest a three-part fertilizer
A one-part hydroponic fertilizer is the simplest to measure: one bottle, one dose. If you only ever plan to grow greens, it is a fine choice. I still point beginners to a three-part base. One set covers lettuce now and tomatoes later, so you learn one product and keep it. The extra work is small. You measure three bottles instead of one, add them one at a time and follow the label for your crop.
Whichever you pick, stick with fertilizer made for hydroponics. The Old Farmer’s Almanac notes that soil fertilizers can clog tubing. Start seedlings at half strength (seller figure). I like that rule because it is hard to hurt a young plant by feeding it too little for a week.
How to switch it to Kratky
Leave out step 4, the air pump and air stone. Fill the container so the solution covers the bottom third of each net pot. Do not top it up as the plant drinks. The level drops over time, and the upper roots end up in the air, where they take in oxygen.
Kratky works best for leafy greens. It is not a good fit for fruiting crops like tomatoes, which drink far more over a longer season. A Kratky jar is usually run for one crop without adding nutrients, then emptied and cleaned before the next planting.
What pH and nutrient levels do hydroponic plants need?
Most crops do best at pH 5.5 to 6.5, per University of Missouri Extension guide G6984. Other extensions give wider ranges. Minnesota gives 5.4 to 7, and Penn State gives 5.0 to 7.0 for vegetables. Aim for the middle and you are safe with all three.
When the reading drifts, pH Up and pH Down bring it back. The General Hydroponics pH Control Kit on Amazon includes both. Add a little, stir, wait, and check again with your meter. The kit also comes with a color indicator. I would not rely on it once fertilizer is in the water, for the reason below.
The meters you need
A pH meter and an EC meter are the two tools I would not skip. Missouri Extension advises meters over test strips, because fertilizer dyes can distort the colors. Here is what to look for:
- A pH meter you can calibrate at pH 4 and pH 7. Missouri Extension says to calibrate weekly at those two points. Expect the probe to last 1 to 2 years.
- A bottle each of pH 4 and pH 7 calibration solution. Buy them with the meter so the weekly check is easy.
- An EC meter that can show EC, not only ppm. Expect the probe to last 2 to 5 years.
EC targets for greens and fruiting crops
EC (electrical conductivity) tells you how strong your nutrient solution is. It is shown in mS/cm or dS/m, which are the same number, so 1.2 mS/cm equals 1.2 dS/m. The ranges below are seller figures, so treat them as a starting point. For lettuce and herbs, I would stay near the bottom of the growing range. Stronger is not faster for greens, and pushing them hard can set up the tipburn covered further down.
| Growth stage | Leafy greens and herbs (mS/cm) | Fruiting crops (mS/cm) |
|---|---|---|
| Seedlings | 0.8 to 1.2 | 0.8 to 1.2 |
| Growing leaves | Near 1.2, the low end of 1.2 to 2.0 | 1.2 to 2.0 |
| Flowering and fruiting | Not needed | 2.0 to 3.0 |
If your meter shows ppm
Many beginner meters are TDS meters that show ppm, not EC. A TDS meter measures EC and then converts it to ppm with a factor the maker chooses. Makers don’t all use the same factor, so one solution can show different ppm on two meters. Check your meter’s manual for its conversion factor before you compare readings to the table. Or buy a meter that can show EC, and use the table as it is.
Check your water first
Missouri Extension suggests source water with an EC of 0.2 to 0.8 dS/m and alkalinity of 40 to 160 ppm. It also says warm water holds less oxygen, which is why I keep the reservoir at 70°F or below.
How much light do hydroponic plants need indoors?
Indoors, give plants 12 to 14 hours of light a day, according to the Almanac. It says LEDs suit leafy greens and HID lamps suit fruiting plants. For a first crop of greens, an LED on a timer is the easy choice.
For greens, plan on 25 to 50 watts of LED per square foot, and 40 to 65 for fruiting plants (seller figures). For one shelf or a small tent of greens, a compact panel such as the Spider Farmer SF1000 LED grow light on Amazon is a sensible size. Hang it at the height its manual gives, and raise it if the top leaves start to bleach or curl.
My guide to indoor vegetable gardening has more on placing lights and choosing crops for winter.
What plants grow best hydroponically?
Minnesota Extension names these as good beginner crops:
- Lettuce
- Herbs
- Kale
- Chard
- Mustard
Lettuce is ready in 6 to 7 weeks, and you can often harvest it 3 to 5 times. Tomatoes, cucumbers and strawberries can do well too, but the extension points to outdoor systems in summer for those. If you have a sunny balcony, my balcony vegetable garden guide covers placement and wind.
How to look after a hydroponic garden each week
A small system needs a few minutes most days and a bigger job every couple of weeks.
- Every few days: check the water level (in DWC), the pH, the EC and the water temperature. Look at the roots and new leaves.
- Weekly: calibrate the pH meter at pH 4 and 7.
- In DWC: drain and replace the full nutrient solution every 2 to 3 weeks (seller figure). Let your EC and pH readings guide you too.
- In Kratky: leave the solution alone for the whole crop.
- Between crops: sanitize the container with about 1 tablespoon of unscented bleach per gallon of water, following Minnesota Extension’s guidance. Then rinse it well with clean water and let it air out and dry before you refill it.
I would also keep a simple log. Write down the date, pH, EC and water temperature each time you check. It takes a minute, and it shows you a problem before the leaves do.
Common hydroponic problems and how to fix them
Brown, burnt leaf edges on lettuce (tipburn)
Penn State Extension links tipburn to calcium deficiency. Calcium moves through the plant with water, so fast growth, heat and still air can keep it from reaching new leaf tips. To fix it:
- Add airflow. A small fan near the plants helps.
- Keep the room cooler, and move plants away from heaters and hot lights.
- Feed at the label rate and keep greens near the low end of the EC range. Don’t push the solution stronger to speed growth.
Yellowing between the veins on new leaves
Penn State says this is usually iron deficiency, often caused by pH running too high. Fix the pH first. Bring it back to 5.5 to 6.5 before you add anything else, then watch the new growth.
Root rot
Healthy roots look white or cream. Slimy, brown roots that smell bad are the sign of root rot, which is tied to low oxygen. To fix it:
- Cool the water to 70°F or below. Warm water holds less oxygen.
- Add more aeration. Check the air pump runs and the air stone isn’t clogged.
- Trim the worst roots, then replace the solution and clean the container.
Green algae in the water
Algae needs light. Use opaque containers, and cover every opening: empty net pot holes, gaps around pots and clear tubing. If a container lets light through, wrap it or paint it.
Where to go from here
Once one container of lettuce is going well, add a second crop or a second container. If space is tight, my notes on small space gardening show where a shelf or a corner can hold a small system. Keep that log going. After one crop, you will know what normal looks like for your water and your room.
Frequently asked questions
What is the easiest hydroponic system for beginners?
The Kratky method is the easiest because it has no pump. You fill a container so the solution covers the bottom third of the net pot and let the level drop as the plant drinks. Deep water culture is a close second and adds an air pump and air stone.
Do hydroponic plants need fertilizer?
Yes. With no soil, the fertilizer in the water supplies all the mineral nutrients a plant needs. Use a fertilizer made for hydroponics, because soil fertilizers can clog tubing. A one-part mix is simplest for greens, and a three-part base covers fruiting crops too.
Do I need a pH meter for hydroponics?
Yes. University of Missouri Extension advises meters over test strips, because fertilizer dyes can distort the colors. Calibrate the meter weekly with pH 4 and pH 7 solutions, and pair it with an EC meter to check nutrient strength.
Does hydroponics use less water than soil?
It can. The Old Farmer’s Almanac says closed hydroponic systems use up to 90% less water than growing in soil. The water stays in the system and is not lost to drainage.
How often should I change the water in a hydroponic system?
In deep water culture, a common grow gear seller rule of thumb is to replace the full solution every 2 to 3 weeks, with pH and EC checks every few days. A Kratky jar is different. It is usually run for one crop without adding nutrients, then emptied and cleaned before the next planting.
How long does hydroponic lettuce take to grow?
University of Minnesota Extension says lettuce is ready in 6 to 7 weeks. You can often harvest the same plants 3 to 5 times by cutting outer leaves and letting them regrow.




